                   .:                     :,                                          
,:::::::: ::`      :::                   :::                                          
,:::::::: ::`      :::                   :::                                          
.,,:::,,, ::`.:,   ... .. .:,     .:. ..`... ..`   ..   .:,    .. ::  .::,     .:,`   
   ,::    :::::::  ::, :::::::  `:::::::.,:: :::  ::: .::::::  ::::: ::::::  .::::::  
   ,::    :::::::: ::, :::::::: ::::::::.,:: :::  ::: :::,:::, ::::: ::::::, :::::::: 
   ,::    :::  ::: ::, :::  :::`::.  :::.,::  ::,`::`:::   ::: :::  `::,`   :::   ::: 
   ,::    ::.  ::: ::, ::`  :::.::    ::.,::  :::::: ::::::::: ::`   :::::: ::::::::: 
   ,::    ::.  ::: ::, ::`  :::.::    ::.,::  .::::: ::::::::: ::`    ::::::::::::::: 
   ,::    ::.  ::: ::, ::`  ::: ::: `:::.,::   ::::  :::`  ,,, ::`  .::  :::.::.  ,,, 
   ,::    ::.  ::: ::, ::`  ::: ::::::::.,::   ::::   :::::::` ::`   ::::::: :::::::. 
   ,::    ::.  ::: ::, ::`  :::  :::::::`,::    ::.    :::::`  ::`   ::::::   :::::.  
                                ::,  ,::                               ``             
                                ::::::::                                              
                                 ::::::                                               
                                  `,,`


http://www.thingiverse.com/thing:3378694
Ender 3 Pro Wire Clips by TheToddRod is licensed under the Creative Commons - Attribution - Non-Commercial license.
http://creativecommons.org/licenses/by-nc/3.0/

# Summary

Update 1 - 1/31/19

The update for version 2 reduces the space between the clip and the frame which makes the clips fit tight to the frame.

Added 2 photos comparing the differences between version 1 and version 2.

Uploaded the version 2 .stl files and the version 2 .gcode files.
Version 2 files are labeled with V2 in the file name. Below is what the V2 files should look like in the downloads section.

Ender 3 V2 Ribbon Cable clip.stl
Ender 3 V2 Power Supply Wire Clip.stl
CE3_Ender 3 V2 Power Supply Wire Clip Single.gcode
CE3_Ender 3 V2 Ribbon Cable Clip Single.gcode
CE3_Ender 3 V2  3-Power Supply Wire Clips.gcode
CE3_Ender 3 V2 3-Ribbon Cable Clips.gcode
CE3_Ender 3 V2 6-Clips 3-Power Supply and 3-Ribbon Cable.gcode

------------------------------------------------------------------------------------------------------------------------

These clips are for attcahing the ribbon cable and the power suppy wires to the ender 3 frame. The intent is to attach the wires to the back of the clips which allows access to the wires. The clips aren't designed to be removed from the frame, but there is some play between the clips and frame in case removal (at your own risk) is necassary. Before attemping any clip removal, remeber to unattach the wires frist to avoid any damage. I haven't tried to remove a clip from the frame, so I can't recommend a technique. Attached is the .stl file for each clip, the .gcode file for each clip, and the .gcode file for (3 - Ribbon Cable Clips and 3 - Power Wire Clips) 6 clips. I recommend removing any sharp edges from the clips and test fitting the wires in the clip before attaching the clip to the frame.

# Print Settings

Printer Brand: Creality
Printer: Ender 3
Rafts: No
Supports: Yes
Resolution: Fine 0.1mm
Infill: 20%
Filament_brand: Hatchbox
Filament_color: True White
Filament_material: PLA

Notes: 
Use supports only for the ribbon cable clip 40 degrees touching the build plate.